View 1300_39066.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CRYSTAL CLOCK OSCILLATORS
WARRANTY CLAUSE
s 1300 Series
No. 1 2 3 4 5 6 7 8 9 Item Vibration Test Shock Test Drop Test Humidity Test Solder Heat Test Thermal Shock Test Terminal Strength Test Soldering Test Solvent Resistance MIL-STD-202F, TM204D, condition B MIL-STD-202F, TM213B, condition 9,800m/s2 0.5 ms 3 times natural drops on to hard wooden board from the height (see 4 ) MIL-STD-202F, TM103B, condition A MIL-STD-202F, TM210A, condition B (260C 5C for 10 1 seconds) Expose to 100 cycles of extreme temperatures, that is, -40C for 30 minutes then +85C for 30 minutes. MIL-STD-202F, TM211A, condition A (Pull Weighting 0.907 kg) and condition C (Bend Weighting 0.45 kg) Soaking in the soldering bath at +2355C for 51 seconds More than 90% of lead should be covered by solder. After soaking in alcohol for 30 minutes. The markings are not faded out. F/F < 10x10-6 = Condition Specification Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*)
(*) After the tests mentioned above, the electrical specifications are satisfied. Also frequency deviation before and after test should be The electrical specifications are frequency tolerance, Lcc, Tr/Tf, VOL/VOH, duty cycle. Model 1300 Height 50 cm
s 1600 Series
No. 1. 2. Item P.C Test Thermal Shock Test Heat Cycle Test High Temperature High Humidity Test +85C Aging (non operated) Vibration Test Shock Test Condition Temperature: +1212C, Pressure: 2 Atmospheric pressure, Time: 48 Hours 1Cycle: -55C (30minutes)~+125C (30minutes) Number of Cycle: 15 cycles is gas phase 1Cycle: -55C ~ +25C ~ +125C ~ +25C
(30 minutes) (10 minutes) (30 minutes) (10 minutes)
Specification Please see below note.(*) Please see below note.(*) Please see below note.(*) Please see below note.(*) Please see below note.(*) Please see below note.(*) Please see below note.(*) Please see below note.(*) More than 90% of lead or Pad should be covered by solder. Please see below note.(*) The markings are not faded out. Also (*)
3.
Number of Cycle: 10 cycles Temperature: +85C, Humidity: 85%, Time: 250 Hours Temperature: +85C, Time: 720 Hours MIL-STD-202F Test Method: 204D, Test Condition: D (196m/s2 Peak) MIL-STD-202F Test Method: 213B Test Condition: Half Sinusoidal Wave 29,400m/s2 0.5 ms 3 Directions 3 times each Fall Height: 75 cm, 3 Drops on to Hard Wooden board MIL-STD-202F Test Method: 208E Test Condition: Soaking in the soldering bath at +2455C for 51 seconds MIL-STD-202F Test Method: 210A Test Condition: Soaking in the soldering bath at +2605C for 101 seconds After soaking in each solvent, Freon, trichloro-ethane and alcohol for 30 minutes.
4. 5. 6.
7.
8.
Drop Test Soldering Test Soldering Resistance Solvent Resistance
9.
10.
11.
(*) After the tests mentioned above, the electrical specifications are satisfied. Also frequency deviation before and after test should be F/F < 10x10-6 = The electrical specifications are frequency tolerance, Lcc, Tr/Tf, VOL/VOH, duty cycle.
100
WARRANTY CLAUSE
s 1700 Series
Specification No. Item Condition Frequency Tolerance Electrical Spec. 1 2 3 4 5 P.C. Test Heat Cycle Test High Temperature High Humidity Test Low Temp. Resistance Test High Temp. Resistance Test Vibration Test Temperature: +121C 2C, Pressure: 2 Atmospheric pressure, Time: 96 Hours (NONE operative) -55~+100C (NONE operative) 15 minutes at each temp. stage, 100 cycles. Temperature: +85C, Humidity: 85% Time: 1000 Hours (5.5V operative) +100C, 1000 Hours (NONE Operative) -55C, 1000 Hours (NONE operative) 10~500Hz, 1.5 mm (Peak to Peak) or 98m/s2 10Hz~500Hz~10Hz Approx. 15 minutes/cycle Sweep time 6 Hours (3 directions, 2H each) Test Condition: Half Sinusoidal Wave 29,400m/s2 0.1 ms 3 Directions 3 times each Drop Height: 75 cm, 3 drops on to Hard Wooden board Test Condition: Soaking in the soldering bath at +230C for 5 seconds (use rosin frux) Test Condition: Soaking in the soldering bath at +2605C for 20 seconds 500g load is weighed on lead tip for 10 seconds. 50 x 10-6 20 x 10-6 50 x 10-6 50 x 10-6 10 x 10-6 10 x 10-6 20 x 10-6 20 x 10-6 More than 90% of lead should be wet by solderer. 10 x 10-6 No damage on lead Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) ------ Please see below note. (*) ------
6
7 8
Shock Test Drop Test
9
Soldering Test
CRYSTAL CLOCK OSCILLATORS
10 11
Soldering Resistance Terminal Strength Test
(*) After the tests mentioned above, the electrical specifications are satisfied. The electrical specifications are Current Consumption, Tr/Tf, VOL/VOH, Duty Cycle.
s 1800 Series
Specification No. Item Condition Frequency Tolerance Electrical Spec. 1 2 3 4 Heat Cycle Test High Temperature High Humidity Test Low Temp. Resistance Test High Temp. Resistance Test Vibration Test -55~+125C (NONE operative) 30 minutes at each temp. stage, 100 cycles. Temperature: +85C, Humidity: 85% Time: 1000 Hours (Energizing at the upper limit of VDD) +125C, 1000 Hours (NONE Operative) -55C, 1000 Hours (NONE operative) 10~500Hz, 1.5 mm (Peak to Peak) or 98m/s2 10Hz~500Hz~10Hz Approx. 15 minutes/cycle Sweep time 6 Hours (3 directions, 2H each) Drop Height: 75 cm, 3 drops on to Hard Wooden board Test Condition: Soaking in the soldering bath at +230C for 5 seconds (use rosin frux) Test Condition: Soaking in the soldering bath at +2605C for 10 seconds 2times each 500g load is weighed on lead tip for 10 seconds. 20 x 10-6 20 x 10-6 50 x 10-6 10 x 10-6 10 x 10-6 20 x 10-6 More than 90% of lead should be wet by solderer. 10 x 10-6 No damage on lead Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) Please see below note. (*) ------ Please see below note. (*) ------
5
6
Drop Test
7
Soldering Test
8 9
Soldering Resistance Terminal Strength Test
(*) After the tests mentioned above, the electrical specifications are satisfied. The electrical specifications are Current Consumption, Tr/Tf, VOL/VOH, Duty Cycle.
101
CRYSTAL CLOCK OSCILLATORS
WARRANTY CLAUSE
s 2500 Series
No. 1 Item Thermal Shock Test Condition 1 Cycle: -55C (15minutes)~+125C (15minutes) Number of Cycle : 5 cycles is gas phase 10~55Hz, 1.5mm (Peak to Peak) 55~2000Hz, 196m/s2 Sweep time 6 Hours (3 directions, 2H each) Drop Height: 75 cm, 3 drop on to hard wooden board Test Condition Soaking in the soldering bath at +260C5C for 20 seconds 2 times each or Soaking in the soldering bath at +230C5C for 180 seconds 2times each Test Condition: Soaking in the soldering bath at +230C for 20.5 seconds 5minutes immersion in Fluorinert at 125C5C After soaking in each solvent, Freon, trichloroethane and alcohol for 30 minutes Specification (1)
2
Vibration Test
(1)
3 4 5 6 7
Drop Test Soldering. Resistance Soldering Test Air Tightness Solvent Resistance
(1) (1) (2) (3) (4)
(1) After the tests mentioned above, the electrical specifications are satisfied. The electrical specifications are Tr/Tf, VOL/VOH, Duty Cycle. (2) More than 90% of Lead or Pad should be covered by solder. (3) No bubbles should be observed. (4) The markings are not faded out.
s 2700 Series
No. 1 2 3 Item Thermal Shock Test High Temperature High Humidity Test +85C Aging (non operated) Vibration Test Condition 1 Cycle: -40C (30minutes)~+85C (30minutes) Number of Cycle : 100 cycles is gas phase Temperature: +85C, Humidity: 80~85% Time: 250 Hours Temperature: +85C, Time: 720 Hours 10~2000Hz, 1.52mm (Peak to Peak) or 196m/s2 20minutes/cycle Sweep time 4 Hours (3 directions, 12H each) Test Condition: Half sinusoidal wave 29,400m/s2 0.3ms 3 directions 3 times each Drop Height: 75 cm, 3 drop on to hard wooden board Test Condition: Soaking in the soldering bath at 230C for 3.51 seconds Pre-heat: 150C 60~120 seconds, Peak temperature 245C, 215C min 10~30 seconds 3times each (1) Specification (1) (2) (1)
4
(1)
5 6 7 8
Shock Test Drop Test Soldering Test Soldering Resistance
(1) (1)
(1) After the tests mentioned above, the electrical specifications are satisfied. Also frequency deviation before and after test should be F/F < 10x10-6. = (2) After the tests mentioned above, the electrical specifications are satisfied. Also frequency deviation before and after test should be F/F < 20x10-6. = The electrical specifications are frequency tolerance, current consumption, Tr/Tf, Vol/Voh, Duty Cycle, current consumption (stand-by), stand-by function.
102
MARKING
Marking frequency digits differs according to marking space available. Please refer to below.
s 1300 Series
Model
Output Frequency #1 Pin Location Lot No. (2 digits) Function (ldigit)
JPN
1300 Series: 8 Including decimal point, maximum 7 digits are marked when frequency unit is MHz. When kHz, maximum digits are marked with initial "k". [EX] 14.3181818MHz 14.3181 900kHz 900.00k
s 1600 Series
Model
1600 Series: 8 Including decimal point, 7 digits are marked. [EX] 4.9152MHz 4.91520
Output Frequency #1 Pin Location Week Code JPN
CRYSTAL CLOCK OSCILLATORS
s 1700 Series
Output Frequency(MHz) Frequency Stability
1700 Series: 8 Including decimal point, 7 digits are marked. [EX] 14.31818MHz 14.3181
Model
Lot No.
s 1800 Series
Model
1800 Series: 8 Including decimal point, 7 digits are marked. [EX] 14.31818MHz 14.3181
Output Frequency #1 Pin Location
Lot No. (2 digits)
103
CRYSTAL CLOCK OSCILLATORS
MARKING
s 2500 Series
NK TK K : 2560NK : 2560TK : 2570NK Output Frequency
2500 Series: 8 Including decimal point, 6 digits are marked. [EX] 14.31818MHz 14.318
#1 Pin Location
Lot No. (2 digits)
s 2700 Series
: 2700N T : 2700T V : 2780V W : 2770W Y : 2770Y Output Frequency
2700 Series: 8 Including decimal point, 6 digits are marked. [EX] 14.31818MHz 14.318
#1 Pin Location
Lot No. (3digits)
104

▲Up To Search▲

Price & Availability of 1300

	To Download 1300 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .